Home > Time Clock > Kronos 4500 Time Clock Error Codes

Kronos 4500 Time Clock Error Codes

Contents

I tried to resend softkeys and they won't take. Change the value of this applicable procedure/step. (refer to the Timekeeper Terminal Configuration Manual for instructions) This is per the book. Am I also correct that rebooting the device will save the configuration? John says: 04/24/2013 at 8:54 am Joe, We have an old 45G gate access terminal that I need to modify the memory allocation settings. weblink

Press the * key Type in Command 90 and press enter Program procedures 9, 10, 15 and 30 with appropriate values: Proc 9 Step 1 Value 0 or 1 If ASYNC Joe Casaletto says: 11/20/2013 at 1:22 pm I would think that should do it, or download a configuration without all those softkey assignments. I used a paper clip to jumper across 2 of the leads and it did the same thing. Also, the Advanced Device Manager is looking for a "krm" file and I have a "kru" file.

Adp 4500 Time Clock Installation

says: 11/19/2010 at 1:15 pm Joe - I am setting the time on the clock itself. Joe Casaletto says: 09/05/2013 at 3:16 pm Chad, I was going to respond back tonite about the SOFTWR RESET button, but you already got it! I can ping it fine, set pc time and send pc time to clock but initialize update and collect do not work.

says: 11/22/2010 at 3:33 pm Joe - On the unit itself. thoward6471 says: 06/07/2011 at 10:18 am Hi Joe, Do You know where I might can locate a manual for Kronos 3a also is there a big difference in the 2a file Afterwards, I was trying to figure out some new commands so that maybe I could give back to the community. Adp 4500 Time Clock With Quick Punch Version 3.0 For part numbers 8602800-500 through -999 * Firmware update 03.00.05.000.kru (Jun 2010) Version 2.3 For part numbers 8602004-xxx and 8602800-001 through -499 * Firmware update 02.03.08.007.kru (Jul 2010) When

drhodes says: 02/24/2011 at 8:18 am It takes me to configuration menu. Kronos Time Clock Default Password When this is finished you can then hit ** Enter Enter to get out of maintenance mode. After using your instructions we were able to telent into a 4500 clock and make some changes. http://www.joecasaletto.com/joekronos/q-a/comment-page-1/ Bob says: 01/04/2011 at 1:26 pm You can set the 4500's IP address via telnet after you login with options like for example: ipAddr="1.1.1.1″ theres also: subnetMask="fffffff0″ gateway="1.1.1.1.1″ (replace 1.1.1.1) Joe

What if you use the telnet reboot command from this page? Kronos 4500 Time Clock Web Interface We have a new employee that WE ADDED A MONTH OR SO AGO AND FOR SOME REASON HIS DISCARD WARNING DATE IS A WEEK AHEAD OF EVERYONE ELSES. The button on the right labeled SOFTWR RESET is Maintenance Mode. I was able to change the ip address, but did not find the device ID.

Kronos Time Clock Default Password

I have never seen this problem before. Kronos Data Collection devices automate data collection to deliver the reliable, accurate workforce data you need to make fact-based decisions. Adp 4500 Time Clock Installation Thanks, Gal. Adp Time Clock Support Leave a Reply Cancel Reply Name (required) Mail (will not be published) (required) Web site You might also like 4500 Clock: Firmware Update Information on the latest firmware update files (as of

Steven Arends says: 02/10/2013 at 5:42 pm Hi Joe is there any way to creat/modify a pay rule without having a Kronos rep come out and do it? have a peek at these guys If that won't go, do a cold start on the clock. There are two ways to cold start a 400 series clock. Long DIP down…unless last or only clock in series - in that case long DIP middle. Kronos Time Clock Installation Manual

Joe Casaletto says: 04/05/2013 at 8:41 am Do you mean a 4500 clock? mhamilton says: 04/18/2011 at 10:53 am We currently have an ADP 4500 Ethernet 8602800-801 digital clock in our break room at work, because of its location multple associates abuse it (starting See: http://www.joecasaletto.com/joekronos/2012/605/4500_telnet/#more-605 Rwandha says: 02/15/2013 at 7:39 am Hi Joe, i have problems about the Data Service, it's don't working good when I need Archive and Discard data pop up a check over here Thanks P.S.

Any ideas what the problem is? Adp Biometric Time Clock Manual If anyone sends in additional tips they will be added to this page. I get error 99 and 2019 request frame failure error FRANK says: 03/05/2013 at 10:19 am i forgot to mention we were using serial comm with the old clock and are

We are on version 6.1.6.136.

When I am in the timesheet for the new employee the current pay period shows nothing I try to add a punch and it says That date is out of range says: 11/23/2010 at 4:59 pm Joe - I can try. That is just an error log. Kronos 4500 Maintenance Password I want to configure a script to reboot the clocks during off hours, but transfer any run saved data to the server.

I told the customer they may be swiping the wrong card since it kept showing manager mode. Dale says: 08/07/2013 at 9:03 am We have Timekeeper/AS 9.0 running (obviously unsupported) and have a need to dramtically increase the number of our time clocks. We have tried 00000 and other combinations, but cant get in. this content Phil says: 01/07/2015 at 1:03 pm Hi Joe, Do you know if there is any configuration commands which will allow an ADP/Kronos 4500 to communicate via an HTTP Proxy (with authentication

I will send some detailed information to your e-mail address. I tried the reboot a few times with same results. Thank you so much. Three different types.

Joe Casaletto says: 11/18/2010 at 2:57 pm To Gal: Command 90, Procedure 2, Step 1, add 64 to whatever value is in there More information: Display Parameters Proc 2 Step 1 Not sure how to do a cold start on a 45G without my book. Joe Casaletto says: 11/21/2013 at 2:38 pm Darren: It seems as if data sent down to the terminal did not match what it is capable of using. This will do the same thing as unplugging it.

scooter says: 11/16/2010 at 9:27 pm If anyone can provide assistance with downloading departments to the 480 clock for use transferring at the clock it would be greatly appreciated.