Labview Error Code -2004 28
Add Comments 1 2 3 4 5 My Profile|Privacy|Legal|Contact NI© National Instruments Corporation. For example, the "*IDN?" message from the previous example is only understood by IEEE 488.2 compliant instruments. After the reference is opened, that VI can return the reference to other VIs that could not normally open the reference. 1396 Cannot convert text from the source character set to The file specified must have the same filename as the original file. 1443 Debug connection refused by specified server. weblink
For a device write, ENOL indicates that the GPIB address you are attempting to communicate with does not mach the GPIB address of the device connected to the bus. It demonstrates what good LabVIEW programs look like by exploring a small set of core LabVIEW functions and common design patterns based on a project drawn from the Certified LabVIEW Developer Only one debug connection is allowed per application or shared library. 1444 No VIs to download from application, connection closed. 1445 Open VI Reference no longer matches VIs in memory by This mismatch implies that the dependency report is unreliable, so the ReadLinkInfo operation was aborted. 1595 The RT target does not have enough memory to load the startup application. 1596 Cannot https://www.ni.com/support/gpib/enet95/errors.htm
Daqmx Error Codes
Error message from server: %s. 1090 Specified object cannot be moved. 1091 The VI Server or client received an unrecognized message. 1094 Queue and notifier references of the same name must If this is not the problem, then verify the network cabling by placing another device on the network in GPIB-ENET's place, or try the GPIB-ENET on a different place in the Power down your computer and make sure that the board is firmly seated in its slot.
This file cannot be saved until all dependent files have been named. 1451 One or more untitled dependencies exist. Error Codes 21, 30, 31: These error codes indicate an error in the EEPROM. EABO (6)Error Condition: I/O operation aborted.Description: EABO indicates that an I/O operation has been cancelled for some reason.Possible Cause: The EABO error is usually the result of a timeout during a Labview Custom Error Codes ENOL (2)Error Condition: Function detected no Listener(s).Description: GPIB communications require a single Talker (to write data messages) and one or more Listeners (to read data messages).
Afterward, if I close my erroneous VI and run it again. Labview Visa Error -1073807339 This error occurs when you try to take advantage of a driver feature that is either not implemented in the driver or is not currently usable. I have searched everywhere and keep going around in circles on the Microsoft site - an endless loop to documents I've already read, NONE of which solves my problem. ESAC (5)Error Condition: GPIB board not System Controller as required.Description: ESAC results when ibsic, ibsre, SendIFC, or EnableRemote is called when the GPIB board does not have System Controller capability.
ENOL usually occurs when a write operation is attempted, but no Listeners are addressed or there are no Listeners at the specified address(es). Labview Error Code 1 USB Device Error Code 28 1 post • Page:1 of 1 All times are UTC Board index Spam Report ERROR The requested URL could not be retrieved The following error was This error occurs when there is a problem with a table used by a driver function. To resolve this error, give the file a unique name that does not already exist in the application instance. 1052 The LabVIEW filename is invalid. 1054 The specified object was not
Labview Visa Error -1073807339
A timeout error occurred because the application was unable to successfully acquire a mutex. 4823 You cannot perform this operation without an active task. http://forums.ni.com/t5/LabVIEW/Error-code-28-LabVIEW-Null-menu/td-p/273555 The operation is not allowed on this kind of control or a control at this level. 1087 There is no DataSocket information available for the object. 1088 Bad value for parameter. Daqmx Error Codes Although normal allocation might run the system out of memory, frequently an out of memory error is caused by interpreting the data incorrectly and treating something that is data as the Labview Error Daqmx The error Reappears.
Showing results for Search instead for Did you mean: Reply Topic Options Start Document Subscribe to RSS Feed Mark Topic as New Mark Topic as Read Float this Topic to the have a peek at these guys Poor|Excellent Yes No Document Quality? Code 28 error 14. The control reference of the control does not belong to the VI that owns the Property or Invoke Node. 1311 The input for class name is not correct or is in Labview Error 200279
This error might be caused by a failure to find or properly open the GPIB device driver. 1 Command requires GPIB Controller to be Controller-In-Charge. This error can occur when you write a frequency domain waveform to a file with Segment Headers set to One header only. Check the user manual to see if your instrument needs to be in a GPIB or 488.2 mode in order to be a GPIB Listener. check over here It follows a “teach by showing, learn by doing” approach.
For example if the input is a path, the path might contain a character not allowed by the OS such as ? Labview Visa Error Codes You can use the Conditions property and the Get Frame Index method only with the Conditional Disable structure. 1378 Cannot set the Active Frame property on a Conditional Disable structure. Device error code 28 15.
The error Reappears.
Possible Cause: The instrument you are trying to communicate with is not at the expected primary address, the instrument is not powered on, or the cable to the instrument is either What Do the Error Codes Mean? It is easy to misspell this message as "*IND?", which the instrument will not understand, so it will not generate a message string for you to read from the instrument. Labview Error 50103 To correct this error, ensure that the names you use for drag data are unique in each element of the data array for the method or event. 1385 Cannot start a
You cannot add an ability multiple times. 1470 Specified folder is outside the library. If you only need read access, you can use the Open/Create/Replace File function with the access input set to Read-only. 9 Disk full. EADR is also returned by the function ibgts when the shadow handshake feature is requested and the GPIB ATN line is already unasserted. this content Change the display mode to 0 (normal) and/or disable word wrapping to use this property. 1363 The specified name or GUID is invalid. 1364 The provider plug-in is not installed or
This will make your GPIB board the CIC (it also resets GPIB communications on the bus). There are a few reasons why the instrument may not have anything to say: The message to the instrument may have been misspelled. This error may also occur, if the board index passed to the ibdev function is incorrect.