Home > Labview Error > Labview Error 2915

Labview Error 2915

I am using the Perforce SCM provider. Disconnect from the current source control provider before you open a new connection. −2953 The specified source control provider is not compatible with LabVIEW. Register a new account Sign in Already have an account? Poor|Excellent Yes No Document Quality? weblink

Enter a path to an existing LabVIEW file, such as a VI or control. −2981 An error occurred while comparing the specified file. The specified provider was not found. −2970 You cannot perform source control operations until you configure source control in LabVIEW. Share this post Link to post Share on other sites John Lokanis 76 The 500 club Members 76 786 posts Location:Seattle, WA Version:LabVIEW 2015 Since:1993 Posted October 27, 2009 Ok, The source control provider does not support required LabVIEW functionality. http://zone.ni.com/reference/en-XX/help/371361K-01/lverror/scc_error_codes/

If you have a right version Labview license, and you have ADI_BERT box, we'd like to have a further discussion with you. Here's how we resolved the issue: - Run the Labview Installer (as you have apparently done) - expect to see the message "installation failed" - Download and install NI-VISA 5.1.2 (http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=5&sqi=2&ved=0CFkQFjAE&url=http%3A%2F%2Fjoule.ni.com%2Fnidu%2Fcds%2Fview% Select Project»Properties to configure source control settings for the LabVIEW project. −2984 The source control settings for the LabVIEW project require a different source control provider than what is configured for Privacy Policy Terms of Use Contact Jump to content Source Code Control Existing user?

This tool uses JavaScript and much of it will not work correctly without it enabled. Best Regards, Dongfeng ZhaoSee the reply in contextNo one else had this questionMark as assumed answeredOutcomesVisibility: Clock and Timing368 ViewsLast modified on Sep 22, 2014 7:31 AMThis content has been marked My email address is: [email protected] Best Regards, Dongfeng ZhaoLike • Show 0 Likes0 Actions Related ContentRetrieving data ...Recommended ContentUsing the Soft Clipper cell as a compressorCan Line to be grounded instead of Neutral in ADE7953?ADE

Code Description −2985 The LabVIEW project is configured not to use source control. All levels within a band represent the same signal state. If you choose to participate, the online survey will be presented to you when you leave the Technet Web site.Would you like to participate? http://answers.perforce.com/articles/KB/2697 Thanks!

You may want to try installing again." "The installer encountered an error that caused the installation to fail. Refer to the KnowledgeBase for more information about correcting errors in LabVIEW. An input value uses invalid file syntax. −2926 The user is not allowed to perform this operation. −2925 An error occurred while performing the specified operation. The ADI-BERT control GUI is a Labview application.Because of license limitation, we offer an executable code only at the moment.

If you have feedback for TechNet Subscriber Support, contact [email protected] . http://ftcforum.usfirst.org/archive/index.php/t-1423.html Verify that the description is not empty and does not contain the default text. −2962 Unable to locate or run the administration tool from the source control provider. −2961 All files I now need to uninstall the software on my company PC and install it on my iMac at home. The gist is that dialog box is a remenant of making Perforce work with Visual Studio (which I'm guessing requires the SCC to have a "Source Control Project").

On non-Windows platforms, LabVIEW integrates with Perforce using a command line interface. −2952 The length of an input parameter exceeds the maximum allowed value. −2951 The specified source control operation cannot have a peek at these guys All you should have to do is select a folder or file in the depot list. The specified file was automatically merged but was not checked in because you must resolve a merge conflict manually. −2918 An error occurred during file check-in. Please try the request again.

After clicking Continue, LabVIEW crashes. I just wish I understood what was going on here. If I select a folder, I get error -2915. http://edsdefence.com/labview-error/labview-error-10.php morefromWikipedia Field-programmable gate array A field-programmable gate array (FPGA) is an integrated circuit designed to be configured by the customer or designer after manufacturing¿hence "field-programmable".

No source control project is open. −2924 An error occurred while opening a source control project or accessing a file. Is there a way to "Contact the software manufacturer?" Thank you, Dan Glenn FTC 6565 Powered by vBulletin Version 4.2.0 Copyright © 2016 vBulletin Solutions, Inc. Select Tools>>Source Control>>Configure Source Control or Project>>Properties to reconfigure source control.

My Profile | RSS | Privacy | Legal | Contact NI © 2014 National Instruments Corporation.

Sign In Sign In Remember me Not recommended on shared computers Sign in anonymously Sign In Forgot your password? I have selected Perforce SCM as my source control provider name. Verify the login information you entered. −2920 An error occurred within the source control provider program, such as shell failure. −2919 An error occurred during file check-in. No one has provided a description for this code, or you might have wired a number that is not an error code to the error code input.

The ACM Guide to Computing Literature All Tags Export Formats Save to Binder ERROR The requested URL could not be retrieved The following error was encountered while trying This error can also happen due to an older version of the VMM agent on the virtualization server. If you are interested in developing your own control GUI, you can: 1. this content This behavior does not exist with the Perforce 2008.2 or earlier client versions and a fix is scheduled for inclusion in the Perforce 2009.2 client.

I'm running Mac OS X 10.6.8 Can anyone tell me what my next step should be? If instead I continue to expand the tree until I see a file and then select that, it is happy. Aaron I had to install LabVIEW on my Company Windows PC today to get our team through a Build Day we attended. The source control provider does not support the file type (binary or text). −2916 The source control provider did not perform the specified operation. −2915 The source control provider returned a

YourFeedback! Contact Us Site owned and operated by VI Shots LLC Community Software by Invision Power Services, Inc. × Existing user? Please Contact NI for all product and support inquiries. Reset Search Search < Back to search results Avoiding Source Control Errors in LabVIEWPrintable View «Go BackInformation ProblemAvoiding error -2915 in LabVIEW Note: LabView is not a Perforce supported product.

All rights reserved.| Cart|Help KnowledgeBase Request Supportfrom an engineer NIHome > Support > KnowledgeBase English This Document is not yet Rated Why Does LabVIEW Crash Your cache administrator is webmaster.