Home > Konica Minolta > Konica Minolta Warming Up Error

Konica Minolta Warming Up Error

Sign up! The "authorized fix" from Konica Tech Support is to open the toner compartment door to expose the Image Transfer Belt Assembly and near the top you should see a metal plate by billc987 on May 16, 2009 at 5:07am Add comment Please sign in to comment The Service Manual in the 2300DL(FATAL ERROR CODE:16H) / 2350(SERVICE CALL 16 XFER BELT) says 16H You are right these codes related to fusing unit. weblink

by Konica-Minolta Tech on Sep 7, 2006 at 2:53pm Add comment Please sign in to comment Hi. I keep wiping it away, but a couple of times every day the printer stops working and reports that the [say] Black cartridge is not installed. troubleshooting procedure overviewpage 368................................................................................................................................................................ As I print more pages, the downward shift becomes less noticeable.

You can print your Parts List or export to Excel to further work with him. Ready indicator Error indicator ... Konica Minolta...

I believe that the Di1610 only has 128kb of onboard memory. Any help would be appreciated.Sept 8-08Issue was the gears on plastic sprockets not meshing properly. I believe the tech will have to turn that on though. Tell them to humor you and replace the sensor and maybe the harness.

I wipe it away, clean the gold contacts on the cartridges, and it works again until the next time it stops. I tried to put tape on the little switch, without the bottle in, and it still says the bottle is full. To print the manual completely, please, download it. http://www.manualslib.com/manual/865215/Konica-Minolta-Bizhub-160f.html?page=281 I tried the obvious solutions (replacing the cartage, turning it off for a few minutes etc).

CAUSE: PU1 has failed. Enter the Administrator Mode and change from "Fusing stability priority" to "Speed priority". 2. It's been really good printing good quality photos and everything. Could you please advise exactly which sensors you replaced?

I'm embarrassed to say I don't know what the OPC is....Thanks again,Joel by unknown on Sep 11, 2007 at 10:47pm Add comment Please sign in to comment 0 I have a http://www.fixya.com/tags/warming_up_error/browse/konica_minolta Sometimes it also fails to pick paper when only a small amount of paper in tray too, even though the tray is lifted. Here it says "Press in the toner carousel latch" but has no further information for where to find this latch; and there is no diagram with a label saying "caousel latch". Modify your browser's settings to allow Javascript to execute.

by Anonymous on Nov 27, 2007 at 8:43pm Add comment Please sign in to comment 0 Hi, Sorry - I am only a user with some knowledge of 2300w and 2400w http://edsdefence.com/konica-minolta/konica-minolta-error-log.php Restore password × Upload manual upload from disk upload from url Thank you for your help! × AdBlocker Detected! I realized the tonor rack was getting jammed against these two plastic tabs that are attached to the inside of the door on the front face of the printer (presumably for If something requires cleaning could you point me to a dissasembly guide and also tell me what solution I could use (I'd rather use a household product - meths, white spirit

Put fuse into slot, ( careful not to break it ) Replace drum, close door, turn power on. I have been so so dissappointed with the feed problem. Started getting toner around edges of sheet and then turned into a 4" band of blue across entire front and back of sheet.I put the old unit back in... http://edsdefence.com/konica-minolta/konica-minolta-error-t00.php this is a common issue where the lead on the board to the main motor blows out.

Konica Minolta has just changed service companies and have moved from Getronics to Laserfast. We reinstalled it several time and receiving the same error massage. by moe on Sep 20, 2007 at 2:41pm Add comment Please sign in to comment 0 Well, I tried cleaning the bottle with warm water, and cleaned the inside.

Konica-Minolta bizhub 215 giving c3451 error message?

by smintx on Jul 17, 2008 at 8:47pm Add comment Please sign in to comment 2 I do not know your printer, but sensors never go bad. However, I cannot rotate the carousel, even while pressing hard enough down on the latch to keep it down.Can anyone tell me where to find the "toner carousel latch", on the The jamming has actually stopped but I have only printed a couple of dozen pages bec the print is still starting much lower than the set margins [the printing starts 2 Our is set to speed and the warming up issue still there.

Any info would be greatly appreciated. There is a small slider (black) that is held in place by a spring. It would be greatly appreciated. this content This page requires Javascript.

If yes, do you know which one? by jeffreyandrew on Apr 14, 2008 at 7:48pm Add comment Please sign in to comment Considering that not too long ago, I saw these at Fry's for $149 refurbished, it makes