Home > Konica Minolta > Konica Minolta I Unit Error

Konica Minolta I Unit Error


Should be doing that soon with the color toners..BB by bbeck500 on Oct 4, 2007 at 11:28pm Add comment Please sign in to comment 0 I am told this is the Where should i start?thanks in advance.sailermanPS I used to work at kmbs. I shut if off, restarted the printer and tried again - same thing. If something requires cleaning could you point me to a dissasembly guide and also tell me what solution I could use (I'd rather use a household product - meths, white spirit weblink

Results 1 to 6 of 6 Thread: Bizhub C253 --- Modem Unit error. It is Konica C220.Before this sometimes when printing in color, part of the page would be in color and the rest would be in black and white. Replace the waste toner box.Replace transfer roller unitThe time to replace the transfer roller has been reached. Any ideas? http://manuals.konicaminolta.eu/bizhub-C554-C454-C364-C284-C224/EN/contents/id16-0048.html

Konica Minolta Imaging Unit Reset

Find the ram clear button and select that and exit out. When I attempt to replace it, the message displayed is "CANNOT ROTATE CARTRIDGE". The ITB is a pretty critical component to image formation, so you may want to invest in having an authorized technician to do the repairs. - Anonymous 1 To yellowLine designs:

I'm not sure how the printer determines the paper size as it feeds into the printing mechanism, but it seems to be misreading the dimensions.I've found a couple other posts on I have 2400w that I am ready to chuck out the window. If the message appears, contact your service representative.When a Waste Toner Box is full When the Waste Toner Box is full, the following message appears (at replacement by user). Konica Minolta Drum Chip Reseter Tool The unit is now apart to the laser unit.

I read about cleaning all the rollers and I did so thoroughly. Konica Minolta Imaging Unit Life End One has printed 7,000 pages and the other has printed 17,000 pages.They both have a problem where they successfully print a job and then quit with a flashing yellow error light Any help would be appreciated!

Any suggestions?

Find the small fuse in the lower right corner. Konica Minolta Waste Toner Box Installation Error I looked and the toner is not turning. best regards Reply With Quote 04-12-2012 #5 Taminol View Profile View Forum Posts Private Message Senior Tech 100+ Posts Join Date May 2007 Location London Posts 148 Post Thanks / Like It is held by one very small screw.Teddyboy49 - Anonymous 0 Thanks, Magnapro, for the suggestion!

Konica Minolta Imaging Unit Life End

Can anyone please tell me how to get to it and clean it, and if they do not beleive this is the issue, can you please advise me as to what http://www.fixyourownprinter.com/posts/40820 As I live abroad, I cannot get a new bottle. Konica Minolta Imaging Unit Reset The color ends up smudging all over the place, but the black and white portion is ok.The consumables are all original. Konica Minolta Bizhub C252 Fuser Unit Reset KonicaMinoltaAcademy 42,000 views 1:42 Testing of Konica Minolta Bizhub C550 - Duration: 2:26.

Your procedure worked perfectly and saved me trawling through the service manual....cheers Reply With Quote 04-12-2012 #6 habik View Profile View Forum Posts Private Message Field Supervisor 1,000+ Posts Join Date have a peek at these guys I recently purchased one of those refill kits for this particular printer. Create your Spare Parts List. Video Photos Link Add Upload Upload × × Draw a box over the problem!! Konica Minolta Imaging Unit Chip Resetter

Any help would be appreciated.Sept 8-08Issue was the gears on plastic sprockets not meshing properly. That should remove the message... My 2400w was blinking the error light steadily (even after restarting it -- green ready would come on briefly, then yellow blinking error again) as if there was a paper jam check over here Loading...

Is this a technical error or are there any adjustments I should make on the printer settings? Bizhub C35 Imaging Unit Reset The image is shifting down the page when it prints about 2-3". I have changed all the toner cartridges and recently the Drum.

Thank you! - unknown 1 Hi,I have two 2300DL Printers.

The printer is being restarted. This will last for about a month and then it will lose its tack again. not even toner. Konica Minolta Printer Troubleshooting Mine are visibly not in alignment with each other... (not all flat on the same plane - the only-just-visible black cartridge is slightly deeper in than the cyan cartridge, which is

I do not feel that it’s an Imaging Unit problem. please help!? Any ideas on what to do? http://edsdefence.com/konica-minolta/konica-minolta-error-m2.php Add to Want to watch this again later?

Then after fill, hold cartridge level and gentle shake left to right, I never had this problem again. that lower gear one might be broken by the pin slot. This does not mean the cartridge is empty so care must be taken that you do not overfill. Wire or foil should be removed after resetting 'just in case'.Refilling the toner cartridges is simle on this model.Teddyboy (In U.K.) by unknown on Dec 6, 2007 at 11:18pm Add comment

I wipe it away, clean the gold contacts on the cartridges, and it works again until the next time it stops. I haven't done this before, so any help would be appreciated!! by ccscomputers on Jan 6, 2011 at 12:57pm Add comment Please sign in to comment 1 I have a net connected 5430DL, it will boot up and the 'Ready' light will Removing these two plastic tabs with a dremel cutting tool was sufficient to clear the fatal error and now the printer works fine.

When I try to print a Test page the printer the grinding noise gets very loud and the page comes out about a 1/4 of the way the the printer shuts The connection is good, but it won't print. After removing a paper jam, the status window now keeps reporting that the printer cover is open even though I have double-checked that it is down all the way. by javaman7471 on Jun 1, 2011 at 7:59am Add comment Please sign in to comment 1 Hi,I need some help here, we have a new Minolta and we just used it

If that doesn't work remove all of the toner cartridges manually and reinstall.Turn off the printer and open the top cover. It was printing fine before you "refilled" it. You can't post answers that contain an email address. I'm tired of this!

What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account? Replace toner and close front door.The time to replace the Black toner cartridge has been reached. it should be fine. - seriously 0 I don't know how that waste bottle works, but on other models I've worked on there was either a fuse that blew when installed if you open the printer up and removed the green drum, at the back in the middle are two small plastic flags that drop through holes where the paper runs.

It has to be collated because otherwise I get 100 of 1 page front and back and 100 of the other page front and back. I installed it on a windows machine to see if the status monitor would shed any light, but the status monitor gives me the 'printer off/printer not connected error'.I've done a Replace the toner cartridge.Replace image transfer belt.