Home > Konica Minolta > Konica 7145 Hdd Error

Konica 7145 Hdd Error

Contents

Remove the developing unit. 2. Page 90: Operation Unit Control, Composition Of Operation Unit OTHER CONTROLS 11.4 Operation Unit Control 11.4.1 Composition of operation unit SGND SUB_SW PSW2B LCDB INV2 PAKB (OPTION) Symbol Name Function or Register] keys do not appear on the [Registration/ Edit Menu].This occurs when the [Entry Function Available] feature is set to [YES]. Remove the RADF. 2. http://edsdefence.com/konica-minolta/konica-error-t81.php

Periodically replaced parts/cycle • Fixing sensor assembly: Every 480,000 copies (7145) • Fixing sensor assembly: Every 400,000 copies (7235/7228/7222) B. Page 16 SAFETY AND IMPORTANT WARNING ITEMS WARNING: Safety Checkpoints • After replacing a part to which AC voltage is applied (e.g., optical lamp and fixing lamp), be sure to check specify other various settings. Remove the air duct [2]. 10. http://www.copytechnet.com/forums/konica-minolta/12741-konica-7145-hdd-error.html

Konica Minolta Bizhub Error Codes

Reinstall the above parts following the removal steps in reverse. 3-13... Fit the long convex end [2] of the drum [1] into the rear side of the unit, then set the drum down into the unit. If any caution label has come off or soiled and therefore the caution cannot be read, contact our Service Office.

Only one side of the AC power line is discon- Composition nected when the main power of this machine is turned off. Page 112: Removing The Optics Wire SCANNER SECTION Removing the Optics Wire A. Procedure 1. Konica Minolta Error Code 107 Remove the 3 screws [3] (SEMS II: long screws), and remove the write unit [4] by pulling it to the paper exit side.

Page 49: Scanner Section, Composition SCANNER SECTION UNIT EXPLANATION 1. Konica Minolta Error Deletion Set the unit so the drum is to the top. 3. Page 144: Removing And Reinstalling The Fixing Unit, Fixing Unit FIXING UNIT 9. http://tomdownload.net/software/konica-7145-hdd-error/ Bit Functions Default values Japan Inch Metric DIPSW6 Timing for the polygon motor to stop/start to rotate at low speed Setting for the polygon motor to stop/rotate at low speed DIPSW7

Overheating may occur there, leading to a risk of fire. • Check whether dust is collected around the power plug and wall outlet. Minolta 6001 Error Codes List Do not remove caution labels. Page 53: Aps Control SCANNER SECTION B. Page 172 MODIFICATIONS NOT AUTHORIZED BY KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.

Konica Minolta Error Deletion

Page 126: Removing And Reinstalling The Transfer And Separation Corona Unit, Replacing The Transfer And Separation Wires Removing and Reinstalling the Transfer and Separation Corona Unit A. Main body Right side <7145> CAUTION The fixing unit is very hot. Konica Minolta Bizhub Error Codes Procedure 1. Konica Minolta Bizhub C6000 Error Codes Open the ADU door [1], and open the convey- ance unit [2].

Page 106: Removing The Platen Glass/slit Glass SCANNER SECTION Removing the Platen Glass/ Slit Glass When removing the platen glass, execute only the steps 1, 3, 7, 8 and 9 in this content Page 23 SAFETY AND IMPORTANT WARNING ITEMS Front side <7145> 7322sf003e CAUTION You may be burned or injured if you touch any area that you are advised by any caution label Page 136: Replacing The Double Feed Prevention Roller A. Periodically replaced parts/cycle • Paper feed rubber: Every 480,000 copies (Once for every 200,000 copies for actual durable count) (7145) • Paper feed rubber: Every 400,000 copies (Once for every 200,000 Konica Minolta C451 Error Codes List

Page 164 Corporate Publications Department © 2004, KONICA MINOLTA BUSINESS SOLUTIONS U.S.A. , INC. Remove the two fixing heater lamps. 5. AlekZubri Service manual link not working (((((( dphuk I didn't, sorry, you can see it here (http://www.scribd.com/doc/128116710/SvcFieldC450) but it's not downloadable If you do get a copy please let me know http://edsdefence.com/konica-minolta/konica-fax-error-t81.php Page 21: Indication Of Warning On The Machine Caution labels shown below are attached in some areas on/in the machine.

or it's affiliates. Konica Minolta Fax Error Codes In the case of the 7145 Remove the E-ring, and then remove the fixing idling gear/B [4] and gear [3]. If further assistance is required, please contact your local service representative.Error Code Recommended Troubleshooting  N-1Check the network cable connection      N-2Conduct JOB deletion       Internet fax reception error   1)Check the settings used during transmission with the sender, then

OUTLINE OF SYSTEM [16] [15] [14] [19] [10] [12] [13] [18] [11] [17] 7322ma1001...

Page 3 7145/7222/7228/7235 SERVICE MANUAL APRIL 2004... The email address entered is already associated to an account.Login to post Please use English characters only. Remove the collar [1] and pull out the feed shaft [2]. Konica Minolta Bizhub 600 Error Codes Loosen the 2 screws [1] and remove the front cover [2] and the front door [3]. 5.

Paper feed roller 4.5.5 Registration clutch drive M9 (Paper feed motor) MC1 (Registration clutch) 1-12... And then install the angle adjustment member [4] in the specified position. Page 166 LD2 offset adjustment (7145 only) ........ http://edsdefence.com/konica-minolta/konica-error-n54.php Click "Add" to insert your video.

Printer 7. Page 44: Bypass Feed Drive, Registration Clutch Drive DRIVE SYSTEM DIAGRAM 4.5.4 Bypass feed drive MC2 (Loop clutch) SD3 (Bypass solenoid) Conveyance roller Driven when SD3 (Bypass solenoid) is on. The CPU on the SCB (System control board) process the data and, based on the results, selects the γ... Page 145: Replacing The Fixing Heater Lamps/1, /2 Caution: • Do not touch the lamp area with bare hands.

Page 116 WRITE UNIT 5. Page 50: Operation, Initial Operation When Power Is Turned On And Shading Correction Reading, Original Reading Mode SCANNER SECTION Operation 1.2.1 Initial operation when power is turned on and shading correction Bit Functions Default values Japan Inch Metric DIPSW20 Separation of defective part Normal Not allowed to of Network Separation of defective part Normal Not allowed to of IEEE1284 Separation of defective The result of this error commonly causes the virtual memory to run slow.

Tell us some more! Page 206 25 MODE DIPSW No. Page 99: Removing The Ribbon Cable DRIVE SECTION Removing the Ribbon Cable A. Printer Repair in Salt Lake City, Utah, YP.* 5211 South Green Pine Drive Murray, UT 84123 * USA *Office:(801)506.0277 *Copyright© Office Imaging Systems 2004, All rights reserved.

Procedure 1. Page 48 DRIVE SYSTEM DIAGRAM Blank page 1-16...